Install the crankcase breather tube plug. The cams are driven by a silent-type cam chain for reduced engine friction, and the surfaces of the cam-chain pins are treated with vanadium for lower friction and increased toughness. Tachometer red zone excessive engine rpm range Clock 12-hour display To set the clock: P25 Fuel gauge Remaining fuel when only 1st E segment starts flashing: approximately 2. Overall dimensions are 2075mm x 780mm x 1060mm, with 155mm ground clearance. Remove the left side cover. Pro-Link monoshock rear suspension features optimized leverage ratios and 9-stage preload adjustment for the rear shock. Pull out the bulb without turning.
Insert the front and rear prongs into the prongs Seat lock front and rear stays on the frame. Used oil, petrol, coolant, and cleaning solvents contain poisons Owning and riding a motorcycle can be that can hurt refuse workers and contaminate enjoyable, but you must do your part to protect drinking water, lakes, rivers, and oceans. Riding on tyres that are excessively For safe riding, you should replace the tyres worn or improperly inflated can cause when the minimum tread depth is reached. Do not perform the maintenance. If the index mark on the The drive chain slider need to be replaced if it washer enters the red zone on the label after is worn to the wear limit line. Hot coolant will scald you. If any part of these displays does not come on when it should, have your dealer check for problems.
Loosen the upper lock nut and turn the Lower adjusting nut upper clutch cable adjuster all the way in Lower lock nut to provide maximum freeplay. Make sure no foreign objects enter the reserve tank opening. They may also be required when ordering replacement parts. Install a new sealing washer onto the drain bolt. Start button Hazard switch Switchable when the ignition switch is on. The pads need to be replaced if a brake pad is worn to the indicator. .
Sharing a common frame and engine,the three machines each have a distinct feel and character and feature a riding position and design that is tailored, and will appeal to, a wide variety of riders, with adaptable abilities that cover a range of uses from commuting and sports, to touring. This aerodynamic bodywork also provides significant advantages in air management for added rider comfort, along with a low drag coefficient and effective engine cooling. Turn the pinion using a Check the operation of the brakelight switch. A clean of clean water and dry with a soft, clean motorcycle makes it easier to spot potential cloth. Remove the bolts and rear fender cover. The minute digits start flashing. Install the brake caliper and tighten the 8.
Adjuster Turn the adjuster using the pin spanner and extension bar provided in the tool kit. Drain deposits into a suitable container. Remove the fuse box covers. This is often considered as the safest. Compressed air cleaning or any other cleaning can degrade the viscous element performance and cause the intake of dust.
Turn the adjusting nuts 8. The frame number is stamped on the right side of the steering head. Phillips screwdriver provided in the tool kit Hold the brakelight switch and turn the P. If these occurs, see your dealer as soon as possible. Your dealer meets all road test your motorcycle after each periodic of these requirements. The colour label is attached to the rear fender under the seat.
Important Safety Information: Recommended for riders 16 years of age and older. Have your motorcycle inspected surface. Tachometer red zone excessive engine rpm range Clock 12-hour display To set the clock: P25 Fuel gauge Remaining fuel when only 1st E segment starts flashing: approximately 2. If you put the motorcycle in gear with the side stand down, the engine will shut off. When the 1st E segment of the fuel gauge When the amount of consumed fuel is more than 1. Hold your motorcycle in an upright position.
Have your motorcycle pull safely to the side of the road and stop inspected by your dealer. If you put the motorcycle in gear with the side stand down, the engine will shut off. Start the engine, pull the clutch lever in, and shift the transmission into gear. Engine weight, at 116 pounds, is laudably light. If the index mark on the The drive chain slider need to be replaced if it washer enters the red zone on the label after is worn to the wear limit line.
Pull the main fuse out and check for a blown fuse. To install the rear wheel, reverse the side collars. Riding with a helmet attached to the holder can interfere with the rear Helmet set wire wheel or suspension and could cause a crash in which you can be seriously hurt or killed. What is the variation involving genuine book and on-line book? Loosen the rear axle nut, lock nuts and turn the adjusting nuts so the rear wheel can be moved all the way forward for maximum drive chain slack. A single front 320mm wavy disc and two-piston brake caliper is matched to a 240mm rear disc and single-piston caliper.
The cylinder head features four solid attachment points for engine hangers, which allows the rigidity of the engine to add to chassis rigidity. Shift the transmission to Neutral indicator comes on. Pull the clip out of the hole. You do not have to check the battery hydrogen gas during normal electrolyte level or add distilled water. The crank counterweight is specifically shaped for couple-balance and its light weight allows the engine to spin freely, with reduced inertia. Some labels warn you of Read instructions contained in Shop Manual potential hazards that could cause serious carefully.