A false blocked condition will either self clear or clear after a key cycle. Ford recommends the use of a digital or dial-type tire pressure gauge rather than a stick-type tire pressure gauge. . Repeat this procedure for each additional transmitter if desired. Plug the power cable into the 12V power point in the vehicle. Step back while the pressure releases.
They don't have 2013 on there at all. Disconnect the electrical connector 1 from the lamp assembly. This allows residual fuel to drain back into the fuel tank and not spill onto the vehicle. Running the system without a filter in place could result in degradation or damage to the system. After idling for a few seconds, release the parking brake, apply the brake, shift into gear and drive. The tires may fail and injure a passenger or bystander.
The turn signals will flash for as long as the lever is held in this position. Some oil must be removed from the engine by an authorized dealer. Replace the air filter housing cover and secure the clamps. A pop-up screen will confirm when it is saved. It is important to reset fuel economy after setting the speed control to get accurate highway fuel economy readings.
You are strongly urged to buy a reliable tire pressure gauge, as automatic service station gauges may be inaccurate. Unlatch and lift the seat out of the tub in the floor by squeezing and pulling up on the handle. If a replacement oil filter is used that does not meet Ford material and design specifications, start-up engine noises or knock may be experienced. The lap belt portion of a combination lap and shoulder belt should be positioned low across the hips below the belly and worn as tight as comfort will allow. The system will automatically provide outside air to reduce window fogging. This workshop manual contains fully detailed step-by-step repair procedures with hundreds of very high quality photos and illustrations to guide you through any repair, maintenance, overhaul, service specifications or troubleshooting procedure.
When the brakes have cooled down, the system will regain all features. Child booster seats The belt-positioning booster booster seat is used to improve the fit of the vehicle safety belt. Ford production and Motorcraft replacement oil filters are designed for added engine protection and long life. It is designed to last the life of the vehicle. Be sure the steering wheel motion is not obstructed by any objects. Ford is also allowed a final repair attempt in some states.
When the system is off, outside air is prevented from entering the vehicle through the vents. A Haynes repair manual is based on a complete teardown and rebuild of the Fifth generation Explorer by Ford. Remove the hood overslam bumper tower to service sidemarker bulb if needed. You can replay approximately 45 minutes of audio as long as you have remained tuned to the current station. These vehicles can only be detected once they have moved fully into your lane. Stow the center head restraint if equipped by pressing the head restraint release button while sliding the head restraint fully down. You need only lightly touch the control graphic to activate the feature.
Display Mode Press the right arrow on the left steering wheel mounted button when display mode is selected. This will automatically return the vehicle to the previously set speed. Repairs will be made using Ford or Motorcraft parts, or remanufactured or other parts that are authorized by Ford. If you choose to install a remote start system please see your authorized dealer for a Ford-approved remote start system. Note: This feature defaults to off, but it must be turned on in order for you to choose and set a category. The tone pattern will repeat periodically until the problem and light are repaired.
Refer to Message center in the Instrument Cluster chapter for more information. Attach the trailer to the vehicle without the weight distributing bars connected. You can print one page at a time. The feature disables outside of R Reverse and must be re-enabled the next time the vehicle shifts into R Reverse. Turns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. Do not modify the front end of the vehicle. First, position the filter in its housing making sure that the far forward end is all the way up in the housing.
The driver is responsible to assess and correct as necessary the final parking position and put the vehicle in P Park. The exterior lamps will flash twice. Use of any tire or wheel not recommended by Ford can affect the safety and performance of your vehicle, which could result in an increased risk of loss of vehicle control, vehicle rollover, personal injury and death. Direct the outer instrument panel vents towards the side windows. Failing to do so may result in loss of vehicle control, which could result in serious injury. Refer to Engine coolant in the Maintenance and Specifications chapter. The brake pedal must be pressed just like for any typical braking situation.
In addition, the driver can temporarily increase the vehicle speed above the current speed by manually pressing on the accelerator pedal. Select the desired temperature using the temperature control. Note: Please refer to local regulations when disposing of transmitter batteries. Measure the height from the center of your headlamp to the ground 2 and mark an 8 foot 2. The airbag may not inflate properly and might force an object into that person causing severe injury or death.