Use only the original valve cap. The exterior design of the Toyota Highlander 2014 a completely new car radiates strength. Without multi-information display: Continue to press and hold the button until the trip meter displays ě000000î. Thanks for choosing FixYa for assistance, a FixYa rating 4 blue diamonds would be greatly appreciated. Turn the ignition off and then start the engine to verify the indicator has been reset. If the warning light turns on within several hours after adjusting the tire pressure, the tire may have a slow air leak. On my 2003 Sequoia, I can cause this condition at will, simply by braking so hard that I trigger the anti-lock brakes.
Tire pressure decreases by about 1. Reportedly, in addition to featuring new interior, the cabin of the 2014 Highlander is much quieter thanks to the development of damping. Torque the drain plug to 30 foot-pounds with a torque wrench and a six-point socket. Emissions Coverage: Coverages vary under Federal and California regulations. Also have 2006 Prius with 150,000 and change it at the same 7,000. Oil changes are the most common reason for the maintenance reminder to illuminate.
Lower the Highlander until only the jack stands support the Toyota's weight. There could be two reasons it is saying its off. This is an information site where you can solve your car problems. Jan 29, 2016 You should change your engine oil and oil filter at 3000 miles with a good brand engine oil then change it every 5000 miles or 6 months which ever comes first. The 2010 Highlander came standard with a 2. Write in the search box the car name for which you want to find information, and find how to reset other service reminders by yourself.
Accordingly, the system may not function properly. This allows you to tighten the oil filter cap without the O-ring bunching up. You can find out by contacting your local dealer or looking it up online at the National Highway and Safety Administration. Many parts stores perform this task free of charge. Ensure Trip Metre A reading is shown. You will see a line go across the trip meter display, this will reset your maintenance required light.
Or any warning light for service reminder which appears on the display. To remove used engine oil from your skin, wash thoroughly with soap and water. Ensure that the tire pressure warning light comes on. Now release the black trip meter reset stick. Free video instructions on how to reset maint reqd on Toyota prius go to www.
First, reset both trip meters A and B. This is an information site where you can solve your car problems. I believe this fault is under recall by Toyota. Individuals leaving comments are solely responsible and liable for the contents of their comments. Allow the oil to drain from the oil filter drain plug.
The synthetic oil Toyota dealers use and those purchased at local outlets will always be Group 3 base oil products which are still manufactured from crude oil that has been highly refined without using solvents in the de-waxing process. Ensure odometer reading is shown. Turn key off no electrical 4. The initialization process is completed when the signals from the tires including the spare tire have been received. The tire pressure warning light will flash 3 times to indicate that initialization has started. Retighten the nut to the specified torque, and then check for air leaks with soapy water.
Please allow us to assist you The maintenance required light is there to remind you that your oil change is due. Or reset check engine light, airbag light, inspection key or insp errors when maint reqd, for Toyota cars. Fuses generally control , for example, all the rear tail lights, or all the front parking lights, etc. Ensure Trip Metre A reading is shown. Remove the oil filter drain plug -- the metal screw in the middle of the oil filter cap -- with a ratchet and a hex-bit socket. When a sensor is defective, remove the battery from the sensor and dispose of properly. This is an information site where you can solve your car problems.
While holding down the trip meter reset knob turn the ignition to run one position before starting engine. This will remove any debris, metal shavings, etc. If the warning light is still on even though the tire pressure is correctly adjusted, the tire could be punctured. Or any warning light for service reminder which appears on the display. If the system fails to reaset, the light will continue flashing. When the viscosity does change the result is the oil becomes thicker when cold and thinner when hot thus not providing the desired engine protection. Then each will be disappear, one at a time from the left.